If your Pyne Pod Click 50K vape kit isn’t performing as it should, you’re not alone. This powerful pod system is built to deliver up to 50,000 puffs with 3 × 2 ml prefilled pods and 3 × 10 ml refill containers for extended use. It features a 750 mAh rechargeable battery with USB-C fast charging, an easy-to-read OLED display showing battery life, puff count and mode, plus mesh coil technology for smooth, flavourful clouds.

With its MTL (mouth-to-lung) draw and 20 mg nicotine salt, it’s designed to feel as close to a cigarette as possible while staying TPD and CE compliant.

But like any high-use device, the Pyne Pod Click 50K can develop small problems — from charging issues to weak vapour, burnt taste, leaking pods, or the OLED screen showing errors. In this troubleshooting guide we’ll go through the most common Pyne Pod Click 50K problems and give you easy step-by-step fixes so you can get back to enjoying your vape.

Whether your battery drains too fast, your flavour tastes mixed after switching, or you’re seeing auto-firing or tight/loose airflow, this guide will help you identify the cause and solve it quickly. By the end, you’ll know when a simple clean or pod swap will do the trick — and when it’s time to replace the device entirely.

Problem 1: Pyne Pod Click 50K Not Charging

It can be frustrating when your Pyne Pod Click 50K vape kit refuses to charge. Because this device relies on a 750 mAh rechargeable battery with USB-C fast charging, any charging issue means you can’t enjoy its huge 50,000 puff capacity. The good news is that most charging problems are minor and can be fixed at home.

Common Causes

There are several reasons why your Pyne Pod might not be charging properly:

• Faulty USB-C cable or wall adapter – Damaged or poor-quality cables can interrupt power.

• Dust or debris in the USB-C port – Even small particles can block the connection.

• Weak power source – Charging from a low-power USB port (like a laptop) may not be enough for fast charging.

• Overheated battery – Vaping heavily in Boost Mode (20 W) can warm the battery and temporarily stop charging.

Easy Fixes

Follow these steps to get your Pyne Pod Click 50K pod system charging again:

1. Swap the cable and adapter
   Try a different USB-C cable and a stable wall adapter instead of a laptop port. Using a high-quality charger ensures steady power for fast charging.

2. Clean the charging port
   Use a dry cloth, a soft brush, or a clean cotton swab to gently clear the USB-C port. Avoid using liquids — moisture can damage the contacts.

3. Let the device cool
   If the battery or body feels warm after heavy use, let it rest for 10–15 minutes before plugging it in. This protects the mesh coil and internal chip.

4. Check for deeper faults
   If the device still doesn’t charge after multiple attempts, the battery or internal circuit may be defective. In that case, the safest option is to replace the device or contact the retailer under warranty.

By taking these simple steps, you can often restore charging and keep your Pyne Pod 50000 puffs running smoothly.

Problem 2: Weak Vapour or Muted Flavour

If your Pyne Pod Click 50K vape kit is still working but the vapour feels thin or the flavour tastes muted, it’s almost always a sign of low e-liquid, a tired mesh coil, or a battery running low. Because this device uses 3 × 2 ml prefilled pods plus 3 × 10 ml refill containers (10,000 puffs each set), you can’t replace the coil separately — so checking the pod first is the key.

Common Causes

Pod or Refill Container Running Low
– The 2 ml pod or 10 ml refill container may be nearly empty, so the wick isn’t staying fully saturated.

Coil Worn Out
– After thousands of puffs, the mesh coil inside the pod loses efficiency and flavour intensity.

Chain Vaping or Boost Mode
– Taking puff after puff too quickly or using Boost Mode (20 W) doesn’t give the wick time to re-soak, leading to weaker vapour.

Battery Running Low
– Even before it dies completely, a low 750 mAh battery can reduce vapour output.

Blocked Airflow
– Dust, condensation or an accidental finger over the airflow inlets can thin vapour production and mute flavour.

Step-by-Step Fixes

1. Check Pod & Refill Container Levels
Look through the clear e-liquid window.
If liquid is low → replace with a fresh Pyne Pod Click 10K pod + refill container.
Even if liquid remains but vapour is weak, the coil may be tired → replace the pod anyway.

2. Recharge the Battery Fully
Plug your device into a USB-C cable and a stable wall adapter.
A weak battery can reduce vapour clouds even before it fully dies.
Give it a full charge and test again.

3. Slow Down Puffing & Use Regular Mode
Leave 15–20 seconds between hits so the wick can soak properly.
Switch to Regular Mode (10 W) for steadier performance if Boost Mode overheats the coil.
This prevents dry hits and keeps flavour intensity.

4. Clear the Airflow Holes
Inspect the airflow inlets and make sure your fingers aren’t covering them.
Use a tissue or blow gently through the mouthpiece to clear condensation or dust.

5. Replace the Pod
If you’ve recharged, slowed your puffs, and cleared airflow but vapour is still weak → the mesh coil inside the pod is spent.
Insert a fresh Pyne Pod Click 50K pod to restore full flavour and vapour production.

When to Replace the Device

If weak vapour persists across multiple new pods and full charges, the device’s internal 750 mAh battery may be degrading. In that case, replacement is the only fix.

Weak vapour or muted flavour in the Pyne Pod Click 50K is almost always linked to a low or tired pod, a low battery, Boost Mode or chain vaping habits. With a quick pod swap, full USB-C recharge and slower vaping, performance usually returns to normal.

Problem 3: Burnt or Harsh Taste

If your Pyne Pod Click 50K vape suddenly gives a burnt hit or tastes harsh on the throat, it’s a clear sign something isn’t right. This pod kit is designed with mesh coils for smooth, rich flavour and a 20 mg nicotine salt for a cigarette-like MTL draw, so you should never experience a burnt or dry taste under normal use. Most of the time, the problem comes down to an empty pod, a worn coil, or vaping too quickly in Boost Mode (20 W).

Common Causes

Empty Pod or Refill Container
– When the 2 ml pod or 10 ml refill container runs low, the wick can’t stay saturated and you’ll get a burnt taste.

Burnt or Worn Mesh Coil
– After thousands of puffs, the mesh coil inside the pod degrades, producing a harsh or metallic flavour.

Chain Vaping or Boost Mode
– Taking multiple puffs in quick succession, especially at 20 W Boost Mode, overheats the coil and burns the wick.

Incomplete Flavour Switch
– If the dual-flavour selector isn’t fully rotated, residual liquid can cause uneven wicking and harsh hits.

Low Battery
– A low 750 mAh battery can under-power the coil, leading to inconsistent heating and a scorched taste.

Step-by-Step Fixes

1. Check the Pod and Refill Level
Look at the clear e-liquid window. If it’s empty or very low, refill immediately with a fresh Pyne Pod Click 50K refill container or swap to a new pod. Even if liquid remains but the taste is burnt, the coil inside may be finished — replace the pod anyway.

2. Slow Down Puffing & Switch to Regular Mode
Leave 15–20 seconds between draws so the wick can re-saturate. Use Regular Mode (10 W) instead of Boost Mode if you’re getting harsh hits — it’s gentler on the coil.

3. Fully Recharge the Battery
A low battery can cause uneven heating and burnt hits. Plug into a USB-C cable and stable wall adapter and give it a full charge before vaping again.

4. Complete the Flavour Switch
If you’ve been switching flavours, rotate the selector completely to the next flavour position and take a few clearing puffs. This prevents mixed liquid from scorching on the coil.

5. Replace the Pod
If the burnt taste persists after refilling, recharging, and slowing your puffs, the mesh coil is done. Insert a fresh Pyne Pod Click 50K pod to restore smooth flavour.

When to Replace the Device

If you’ve tried all of the above with multiple new pods and a full charge but still get burnt hits, the internal battery or chip may be failing. In that case, replacement of the entire Pyne Pod Click 50K kit is the only fix.

Burnt or harsh taste on the Pyne Pod Click 50K almost always means an empty pod, a tired coil, or vaping too quickly in Boost Mode. By refilling or swapping pods, slowing down your draw, and keeping the battery topped up, you can restore the smooth, rich flavour this pod system is known for.

Problem 4: Leaking or Gurgling

If your Pyne Pod Click 50K vape starts leaking e-liquid or makes a gurgling sound when you inhale, don’t panic. This high-capacity pod system with 3 × 2 ml prefilled pods and 3 × 10 ml refill containers is designed to be leak-resistant, but like any vape kit it can develop minor leaks or condensation build-up over time. The good news is that these issues are easy to identify and fix at home.

Common Causes

Worn Pod Seals
– After thousands of puffs, the rubber seals around the mesh coil pod can degrade and let liquid seep out.

Condensation Build-Up
– Normal MTL inhaling creates small amounts of condensation inside the mouthpiece; if left uncleaned, it can lead to gurgling and minor leaks.

Over-Drawing or Boost Mode
– Taking very hard pulls or chain vaping at 20 W Boost Mode can flood the coil with too much liquid.

Heat Exposure
– Storing your device in a hot car or direct sunlight thins the e-liquid and makes leaks more likely.

Loose Pod Fit
– If the pod isn’t fully clicked into place, the seal between the pod and battery breaks, causing seepage and airflow noise.

Step-by-Step Fixes

1. Wipe and Dry the Device
Remove the pod and gently wipe the battery contacts and pod base with a clean tissue. Drying removes excess liquid and stops gurgling.

2. Reinsert the Pod Securely
Push the Pyne Pod Click 50K pod back into the device until it clicks firmly. A snug fit restores the seal and prevents leaks.

3. Inhale More Gently
Especially in Boost Mode, take slower, steadier draws. This prevents over-saturating the mesh coil and flooding the airflow chamber.

4. Store Upright and Out of Heat
Keep your device standing upright on a flat surface. Avoid leaving it in hot cars or direct sun, which can thin e-liquid and force it past seals.

5. Replace the Pod if Needed
If leaking or gurgling continues after cleaning and reseating, the seals on that pod are likely worn. Insert a fresh Pyne Pod Click 50K pod to restore normal operation.

When to Replace the Device

If you’ve tried new pods, cleaned the device and changed your draw but leaks persist, the problem could be with the device’s internal seal or battery contacts. In that case, replacing the entire Pyne Pod Click 50K kit is the safest fix.

Leaking or gurgling on the Pyne Pod is almost always caused by worn seals, condensation or over-drawing. By wiping, reseating, vaping gently and keeping the device upright, you can stop leaks and keep your vaping experience smooth and mess-free.

Problem 5: Pod Not Detected / OLED Shows Error Icon

If your Pyne Pod Click 50K vape kit suddenly stops firing and the OLED display shows an error icon or “no pod” message, it usually means the device isn’t recognising the pod. This can happen after swapping pods, refilling, or carrying the device in your pocket. Because the Pyne Pod Click 50K uses a precise connection between its battery contacts and mesh coil pod, even a little dirt or misalignment can stop it from working properly.

Common Causes

Misaligned Pod
– The pod isn’t fully clicked in, so the battery can’t detect it.

Dirty or Wet Contacts
– E-liquid residue, condensation, or dust on the metal contacts breaks the electrical connection.

Flooded Pod
– Overfilling or over-drawing can push liquid into the sensor area and confuse the device.

Empty or Burnt Pod
– A pod that’s out of liquid or has a burnt coil may trigger an error.

Airflow Sensor Blocked
– Debris or condensation can block the small sensor used to detect puffs.

Low Battery
– A low 750 mAh USB-C battery can also cause the pod not to be detected.

Step-by-Step Fixes

1. Remove and Inspect the Pod
Take the pod out completely. Check that it’s filled correctly and the mouthpiece isn’t flooded with liquid.

2. Clean the Contacts
Use a dry cotton swab or tissue to wipe the metal contacts on both the pod and inside the device. Make sure everything is clean and dry — no e-liquid residue.

3. Reseat Until It Clicks
Push the pod firmly back into the Pyne Pod Click 50K until you hear or feel a click. A solid fit ensures the battery recognises the pod.

4. Clear the Airflow Sensor
Blow gently through the mouthpiece or use a tissue to clear condensation from the airflow holes. This helps the puff sensor work correctly.

5. Recharge the Battery
Plug the device into a USB-C cable and stable wall adapter to give it a full charge. A low battery can trigger “no pod” or error messages.

6. Try a Fresh Pod
If the error continues after cleaning and reseating, the coil inside the current pod may be burnt or defective. Insert a new Pyne Pod Click 50K pod from your kit.

When to Replace the Device

If the device still won’t detect any pod after multiple clean pods, full charges, and cleaning, the internal sensor or chip may be failing. In that case, replacing the Pyne Pod Click 50K kit is the safest option.

“Pod not detected” or “error” on the Pyne Pod Click 50K is almost always caused by a loose or dirty pod, low battery, or a flooded sensor. By removing, cleaning, reseating, and recharging, you can quickly restore normal vaping without errors.

Problem 6: Auto-Firing or Device Heating Up

If your 50K vape starts auto-firing (activating without you drawing) or feels hot to the touch, it’s a warning sign. This pod kit uses an automatic draw-activation system and a mesh coil for rich flavour, so it should only fire when you inhale. Auto-firing or overheating can be caused by liquid interfering with the sensor, a faulty pod, or even a failing battery or chip. Left unchecked, it can damage the device or make vaping unsafe — but in most cases it’s easy to stop.

Common Causes

Pod Leakage Interfering with Sensor
– E-liquid leaking from the 2 ml pod or 10 ml refill container can drip onto the airflow sensor and make the device fire on its own.

Faulty Pod or Coil
– A defective pod or worn mesh coil can create shorts or confuse the automatic firing system.

Battery or Chip Fault
– A low or damaged 750 mAh USB-C battery or internal circuit fault may trigger auto-firing or excessive heat.

Step-by-Step Fixes

1. Immediately Remove the Pod
If the device starts auto-firing or feels hot, take the pod out right away to stop power delivery to the coil.

2. Wipe Everything Clean
Use a clean, dry tissue or cotton swab to wipe the battery contacts, sensor area and pod base. Make sure there’s no liquid or condensation anywhere.

3. Let the Device Cool Completely
Place the battery section on a flat surface and let it cool for 10–15 minutes before reassembling. This protects the internal chip and prevents further overheating.

4. Insert a Fresh Pod
After cleaning and cooling, install a new Pyne Pod Click 50K pod to rule out a defective or leaky pod.

5. Check Charging Habits
Avoid charging in very hot environments or leaving the device plugged in overnight. Stable USB-C charging keeps the battery healthy and reduces sensor faults.

6. Stop Using if the Problem Continues
If the device still auto-fires or heats up even with no pod inserted, the internal chip or battery is likely defective. In this case, stop using the device and replace the Pyne Pod Click 50K kit for safety.

When to Replace the Device

Persistent auto-firing or overheating after cleaning and new pods is a sign of a serious internal fault. For your safety, do not keep using it — replacement is the only fix.

Auto-firing or device heating up on the Pyne Pod Click 50K is almost always caused by pod leakage, a faulty pod or a failing sensor. By removing the pod, wiping and cooling the device, and inserting a fresh pod, you can usually stop the issue. If it continues, stop using and replace the kit.

Problem 7: Airflow Too Tight or Too Loose

One of the biggest draws of the Pyne Pod Click 50K is its smooth, cigarette-like MTL (mouth-to-lung) draw. If you notice the airflow has suddenly become too tight (hard to pull) or too loose (very airy, no resistance), it can affect vapour production and flavour. This pod system is designed for a balanced draw, so any change usually means a minor alignment or maintenance issue.

Common Causes

Pod Misalignment
– If the pod isn’t fully clicked in, the airflow path can be restricted or opened up too much.

Condensation or Debris in Airflow Holes
– Dust, pocket lint, or condensation can block or widen the airflow channels near the mouthpiece.

Dual-Flavour Selector Not Fully Rotated
– If the selector wheel isn’t fully turned when switching flavours, it can partially block the airflow.

Loose Seals
– After thousands of puffs, the pod’s rubber seals can wear out, changing the draw tightness.

Step-by-Step Fixes

1. Inspect and Clear the Airflow Holes
Look at the small holes near the mouthpiece and along the pod base. Use a tissue or dry cotton swab to gently clear any condensation or dust. Make sure your fingers aren’t covering the holes while vaping.

2. Clean Pod and Device Thoroughly
Remove the pod and wipe the battery contacts, sensor area, and the sides of the pod. Keeping everything dry restores normal airflow.

3. Reseat the Pod Securely
Push the Pyne Pod Click 50K pod back into the device until it clicks firmly. This aligns the airflow path and seals.

4. Test with a Fresh Pod
If the draw still feels off, insert a new pod from your kit. Worn seals or a tired coil can affect airflow tightness.

5. Adjust Puff Technique
Hold the device so your fingers aren’t blocking the airflow inlets and take slow, steady puffs for a true MTL experience.

When to Replace the Device

If airflow issues persist across multiple new pods and after cleaning, the problem could be with the device’s internal airflow channel or sensor. In that case, replacing the Pyne Pod Click 50K kit is the only fix.

Airflow too tight or too loose on the Pyne Pod Click 50K is almost always caused by misalignment, condensation or worn seals. By cleaning, reseating, and testing with a fresh pod, you can restore the smooth, balanced MTL draw this vape kit is designed to deliver.

Problem 8: Battery Draining Faster Than Expected

One of the advantages of the Pyne 50K is its 750 mAh rechargeable battery with USB-C fast charging, designed to power thousands of puffs per charge. If you notice the battery life dropping quickly or the OLED screen showing low battery after only a few sessions, it can impact vapour quality and flavour consistency. Luckily, this is usually easy to fix with a few simple habits.

Common Causes

Heavy or Chain Vaping
– Taking many puffs in quick succession drains the battery much faster than normal use.

Boost Mode (20 W)
– Using the high-power Boost Mode produces bigger clouds but also doubles the power draw compared to Regular Mode (10 W).

Partial or Incomplete Charging
– Unplugging the device too soon or using a weak power source can result in shallow charges.

Battery Degradation
– Over time and after thousands of recharge cycles, any lithium-ion battery will lose capacity.

Dirty Contacts or Pod Leaks
– E-liquid on the contacts can cause power loss and make the device work harder, shortening battery life.

Step-by-Step Fixes

1. Switch to Regular Mode
Use Regular Mode (10 W) instead of Boost Mode for everyday vaping. It draws less power and extends battery life significantly.

2. Take Shorter Sessions
Allow breaks between puffs to reduce continuous power drain. Chain vaping in Boost Mode is the fastest way to deplete the battery.

3. Give it a Full USB-C Charge
Plug the Pyne Pod Click 50K into a stable wall adapter using a quality USB-C cable. Leave it on charge until the OLED screen shows full battery before unplugging.

4. Store at Room Temperature
Avoid leaving the device in hot cars, direct sunlight or freezing conditions — extreme temperatures reduce battery performance.

5. Clean the Device Contacts
Remove the pod and wipe the battery contacts and pod base with a dry tissue to remove any liquid that may cause power loss.

6. Replace the Device if Needed
If battery life still drops rapidly after full charges, gentle use and clean contacts, the internal 750 mAh battery may be worn out. In that case, replacing the Pyne Pod Click 50K kit is the only fix.

When to Replace the Device

Persistent fast battery drain after all these steps is a sign of normal battery ageing or internal circuit faults. At that point, a new device will be more reliable.

Battery draining fast on the Pyne Pod Click 50K is almost always linked to Boost Mode, chain vaping, partial charges or an ageing battery. By switching to Regular Mode, giving full USB-C charges and cleaning contacts, you can keep your vape running longer between charges.

Problem 9: Flavour Tastes “Mixed” After Switching

One of the standout features of the Pyne Pod Click 50K is its dual-flavour system, which lets you switch flavours easily using the selector. If you notice the flavour tastes mixed or off after switching, it can make your vaping experience unpleasant. This is usually caused by residual e-liquid in the wick or incomplete rotation of the selector — easy fixes once you know what to look for.

Common Causes

Residual Flavour in Wick
– After thousands of puffs, the cotton wick in the mesh coil pod can hold on to a bit of the previous flavour.

Incomplete Rotation of the Selector
– Not fully rotating the flavour selector can leave the two liquids blending together.

Old or Worn Pod
– A tired coil or pod may not handle flavour changes cleanly, especially near the end of its life.

Rapid Switching Between Flavours
– Changing flavours back and forth too quickly doesn’t give the wick time to clear.

Condensation Around Mouthpiece
– Moisture or liquid build-up can mix with new flavours, altering the taste.

Step-by-Step Fixes

1. Rotate Selector Fully
Turn the dual-flavour selector completely to the next flavour position until you feel a click. A full rotation ensures the pod pulls only one liquid.

2. Take a Few Clearing Puffs
After switching, take two or three short puffs without inhaling deeply. This flushes the old liquid from the wick before you vape normally.

3. Slow Down Switching
Give the pod a little time between flavour changes — at least a few minutes or a few light draws — so the wick can adjust.

4. Replace the Pod
If the mixed flavour persists even after clearing and slowing down, insert a fresh Pyne Pod Click 50K pod. A new coil will deliver clean flavour separation.

5. Wipe Condensation Around the Mouthpiece
Use a tissue to dry the mouthpiece and airflow holes to remove any leftover liquid that might be altering the taste.

When to Replace the Device

If you’ve tried all the steps above and still get mixed flavours across multiple new pods, the problem may be with the internal selector mechanism. In that case, replacing the Pyne Pod Click 50K kit is the only fix.

Flavour tasting mixed after switching on the Pyne Pod Click 50K is almost always caused by residual liquid, incomplete selector rotation, old pods or rapid switching. By rotating fully, taking clearing puffs, slowing down changes and replacing the pod, you can restore crisp, clean flavour every time.

Final Words

Most issues with the Pyne Pod vape kit – from charging problems and weak vapour to burnt taste, leaking pods, auto-firing, or mixed flavours – are minor and easy to fix at home.

By keeping your device clean, using the supplied USB-C fast charging cable, allowing the mesh coil to re-saturate between puffs, and replacing pods when performance drops, you can usually restore smooth vapour and full flavour.

Always check the 2 ml prefilled pods and 10 ml refill containers, clean the battery contacts, and give your 750 mAh battery a full charge before assuming the worst. The OLED display is your friend – it shows battery life, puff count and mode so you know what’s happening inside the device.

If, after trying these fixes, your Pyne Pod still doesn’t work correctly across multiple fresh pods and full charges, the safest option is to replace the kit or contact your retailer for support. Batteries and sensors wear out over time, and a new device will always perform better.

With regular maintenance, careful flavour switching and proper charging habits, your Pyne Pod Click 50K can deliver tens of thousands of satisfying, cigarette-like MTL draws with rich flavour and minimal hassle.